Optimization Analysis of Warping of Injection Molding Process of Pipeline Distributor Based on Moldflow

LOU Yan-hua, XU Li-li

PDF(2057 KB)
PDF(2057 KB)
Plastics Science and Technology ›› 2024, Vol. 52 ›› Issue (08) : 113-116. DOI: 10.15925/j.cnki.issn1005-3360.2024.08.022
Computer Aided Technology

Optimization Analysis of Warping of Injection Molding Process of Pipeline Distributor Based on Moldflow

Author information +
History +

Abstract

The material used for the pipeline distributor is polyamide66 (PA66), which is made by injection molding process and analyzed by molding flow by Moldflow software, and the injection molding process is affected by many factors. In this paper, the melt temperature, injection pressure, holding pressure and cooling time are taken as the research variables, and the warpage deformation of the parts is taken as the research objective to establish the response surface model, so as to reduce the warpage deformation of the parts by obtaining a set of better combinations of molding process parameters. The results show that when the melt temperature is 238 ℃, the injection pressure is 50 MPa, the holding pressure is 30 MPa and the cooling time is 110 s, the warpage deformation of the parts is 2.264 0 mm, which is reduced by 2.118 7 mm compared with before optimization, and the overall quality is significantly improved.

Key words

Pipeline splitter / Response surface analysis / Moldflow / Process optimization

Cite this article

Download Citations
LOU Yan-hua , XU Li-li. Optimization Analysis of Warping of Injection Molding Process of Pipeline Distributor Based on Moldflow. Plastics Science and Technology. 2024, 52(08): 113-116 https://doi.org/10.15925/j.cnki.issn1005-3360.2024.08.022

References

1
马小丰,金旺,刘莉莉,等.增韧尼龙66的制备及耐低温性能[J].工程塑料应用,2019,47(6):38-42.
2
崔晶,李应成,林程,等.共聚尼龙66/1212树脂的非等温结晶动力学分析[J].化学反应工程与工艺,2022,38(3):248-253.
3
李瑞娟,黄力.基于BP神经网络的汽车内饰面板注塑成型工艺参数优化[J].塑料,2016,45(3):81-85, 35.
4
顾嘉琦,胡宇宣,郭永环,等.基于均匀试验设计的温控器上盖注塑模具工艺参数优化[J].塑料科技,2017,45(8):67-70.
5
夏新宇,陈勇.基于MoldFlow的汽车水室注塑模冷却管道布局优化[J].山东化工,2021,50(2):162-165.
6
季宁,张卫星,于洋洋,等.基于Kriging代理模型和MOPSO算法的注塑成型质量多目标优化[J].塑料工业,2020,48(5):67-71.
7
刘荣进,王海雄.基于MoldFlow的四通塑料管注射模设计[J].模具制造,2018(7):49-53.
8
黄钢华,张益华,鲁世缸,等.MOLDFLOW/MPI翘曲分析在注塑模中的应用[J].塑料制造,2008(8):64-67.
9
张红,张杰,李奋华.基于计算机辅助工程的供水管路接头注塑同轴度优化[J].塑料科技,2023,51(6):85-89.
10
张新聚,李亚男,刘雷.影响注塑模具成型质量的关键因素分析[J].塑料工业,2018,46(5):71-75.
11
刘强,王霞,宋赛楠,等.注塑成型工艺对管材专用PPH刚韧性能的影响[J].合成树脂及塑料,2019,36(4):38-40.
12
谭波.ABS自动化设备电子元器件外壳注塑成型工艺优化研究[J].塑料科技,2023,51(6):75-79.
13
张继林,罗文翠,唐林虎,等.基于响应面法优化增韧尼龙66切削工艺参数[J].工程塑料应用,2022,50(9):56-63.
14
颜志勇.PLC控制器塑料端子接口注塑成型工艺参数优化[J].塑料科技,2023,51(5):100-103.
15
罗明全,张海,吕韦岑.基于计算机模拟技术的电机外壳注塑成型工艺优化研究[J].塑料科技,2022,50(2):81-84.
16
刘金娥,刘婉慈.自动化传感器外壳注塑成型工艺优化研究[J].塑料科技,2023,51(5):95-99.
17
罗明全,张海,吕韦岑.基于计算机模拟技术的电机外壳注塑成型工艺优化研究[J].塑料科技,2022,50(2):81-84.

Comments

PDF(2057 KB)

Accesses

Citation

Detail

Sections
Recommended

/